2008 BUELL-FIREBOLT-SERVICE-MANUAL FILETYPE PDF

View and Download Buell XB Series service manual online. XB Series Motorcycle pdf manual download. See a Buell service manual for proper torque values. Aftermarket . Typical Buell V.I.N.: Ulysses Models Ignition System: XB Models. ITEM. DATA. T+ .com/

Author: Sataur Mazucage
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Travel
Published (Last): 5 February 2011
Pages: 329
PDF File Size: 2.6 Mb
ePub File Size: 7.54 Mb
ISBN: 122-5-25208-508-1
Downloads: 93908
Price: Free* [*Free Regsitration Required]
Uploader: Gardagar

One narrow fiber plate.

Repeat to verify torque. High beam connection [38] left side with ground Figure On Ulysses models, remove air flow guide. Always discard o-rings after removal. When test is finished, close valve knob turn knob fully sm clockwise. Remove return oil line 7.

Buell Firebolt Service Manual

Strain relief collar 5. Buell Models except Blast Figure Fan actuation is controlled by the ECM. Install footpeg mount 3.

The repair instructions in this Service Manual are by connector Place and Buell-firdbolt-service-manual type. Commutators with more than 0. Separate the adjusting screw 8 from the bearing 7 and release plate 5. Replace housing if any of these condi- tions are found.

2008 Buell XB Models Service Repair Workshop Manual DOWNLOAD

The swingarm features a removable brace on the right side to allow drive belt replacement. Pull ferrule end of cable housing away from bracket. Start the cylinder head screws onto the cylinder studs, two short screws on the left side of the engine, two long bolts on the right. Thoroughly clean and inspect all parts. Do not use the same seal Bearings twice. Inspect seats for cracking, chipping or burning.

  BONO JUANA AZURDUY DE PADILLA PDF

Match the notches in the tool flange to the U-bends in the spring clip. Adjust primary chains not meeting vertical free play specifications.

Install sprocket cover 2 using sprocket cover fasteners 1, 3 and tighten all fasteners and washers 1 to in-lbs Nm. Connect battery cables to battery: On the pin side of the connector, tangs are positioned at the bottom of each cavity, so the slot in the pin terminal on the side opposite the crimp tails must face downward.

Welcome to our Buell forum! Shop performance motorcycle parts.

Remove two screws and washers to detach TP sensor. Muffler Mounting System Fairing Support Bracket Assembly: Filettpe holding tool 2. Pull the lamp assembly away buell-fireboolt-service-manual center tail section pulling the harness out between the tail screen and the buepl-firebolt-service-manual tail section.

Buell-firebbolt-service-manual fork assembly into upper clamp. Tamper-resistant Torx fasteners 2 3. Main drive gear 2. Install seat lock retainer 3 by aligning retainer to retainer sm grooves on back side of seat lock 1.

To prevent leaks, lubricate the o-rings before installation. Front intake cover fasteners with nylon washers 2 models without translucent covers 5. If, through hard usage, the primary chain does become worn and cannot be adjusted to within specifications, it must be replaced.

  DIN 50930 6 PDF

Cycle the actuator to verify cable and valve operation: Tab recesses Figure The charging system consists of the alternator and regulator. For information on the swingarm function as the oil tank, see 3. Hold footpeg 10controlling spring, to footpeg mount 1. Once engine has been removed from vehicle, finish sm removing the following items as required: Horizontal Headlamp Adjustment Fastener Locations: Align front fender 2 to fender mounts on lower triple clamp, apply LOCTITE red and Install sm front fender fasteners and washers 1 and tighten buell-ffirebolt-service-manual Intake flange fastener 2 Figure NOTE Only loosen headlamp alignment fasteners enough to adjust headlamp.

Disconnect and remove Bank Angle Sensor 2 [].

Buell XB Service Manuals and Specs – Buell Forum & Motorcycle Parts

Grab the bulb with paper or and turns on and off with headlight switch. NOTE Buell-firebolt-servcie-manual the rubber boot so the flat on the boot is towards the left side of the motorcycle. NOTE sm The procedure for tightening the head screws is critical to proper distribution of pressure over gasket area.

Author: admin