4116R LF PDF

R. R. R. PIN #1 REF. +/ +/ ). + / ( +/ . LF = Tin-plated (lead free). • Blank = Tin/Lead-plated. The RLF is a thick film Isolated Resistor Network with superior package integrity and compatible with automatic insertion equipment, DIP package of. Buy online R-LF 47 Ohm isolated resistor network by Bourns. Download Bourns R series network resistor t price and availability.

Author: Faujar Mikagal
Country: Oman
Language: English (Spanish)
Genre: Art
Published (Last): 20 August 2012
Pages: 320
PDF File Size: 16.85 Mb
ePub File Size: 3.47 Mb
ISBN: 813-4-28727-746-2
Downloads: 65177
Price: Free* [*Free Regsitration Required]
Uploader: Mejind

R Datasheet(PDF) – Bourns Electronic Solutions

All Activity Home Underskor. Community Reputation 0 Neutral. Sidmonster was on the right track but I remade the wrong cable. A5, not reading the single pot I had connected at J1.


To read the pot, I forced the lines on AIN. Pin 5 of the is J1. A0 – my pot! Looks to be working! Big thanks to SmashTV and the guys on midibox, it was 41116r them. Hope this thread helps someone out one day! At my wits end here, spent the last few nights trying different things but I can’t get anywhere.

Removed all s but J5. A0, and grounded AIN: Still getting a large, constant stream of jitter. I am also now getting an “Unrecognised USB device – device has malfunctioned” tooltip on windows XP which I wasn’t getting before, however if I use the J27 jumper and load the Bootloader, this notification does not occur.


Here is an extract 4116 the jitter so you can get an idea of the volume if that’s relevant: Ah my mistake, I was reading the pin numbers in place of the binary columns for lack of better words.

A0 – 1 J5A. A1 – 2 J5A. A2 – 3 J5A. A3 – 4 J5B. A4 – 5 etc instead of J5A. A2 – 4 J5A. A3 – 411r J5B.

RLF Bourns Bours排阻 DIP ohms

A4 – 16 etc Thanks for both of your replies. The reason I ask is because I’d like to disable all but the first llf J5A. Might be really obvious but it’s not lc for me. Thanks in advance, Tom. Have been away for a while, exams and stuff. Back into it now though.

Clamped the cable down and set the mux control lines up. Anything I can try? Touching pins on J5C causes jitter activity. Touching pins on AIN: J5 also causes activity.

Letting the pot’s input float causes jitter as expected. Have swapped a couple of s in and out with no change. Hope you guys can help: Hi there, What would be the best way to handle several VU meters? Arduino-powered breakout board with a shift register for each meter?

Is it possible to output values with MIOS32? I will admit I am intimidated by the idea of a BLM haha. Multiply this by 10 and I’m lv if it would cause responsiveness issues. I am still only at the very 4116t of the controller design stage so I just want to make sure I don’t design anything that’s impractical.


I had a quick google around for MIDI throughput and 4116 found something from which said it was something like 3. Seems to be working OK, haven’t done much testing though. It’s compact, has a few buttons custom ones can have knobs I believe? The cables are short, maximum 10cm. Are these the correct resistor networks?

Bourns 4116r LF 1-330 Resistor Network

S0 I can even do it by hovering my finger close to said pin. Sometimes, during startup, all connected LEDs will turn on for a few seconds and then all off.

J1 – no luck: Well it works, somehow! Unfortunately though I think I came home after a few drinks l poked around looking for shorts, so I don’t remember exactly where it was.

Thanks a lot for your help julienvoirin! Sign In Sign Up.

Author: admin