CANON IR3300 ERROR CODES LIST PDF

Canon Ir Error Code List. Code Description. E Communication error ( with pedestal). E Communication error (with ASSIST). Free downloads Error Codes Canon iRPage 1 of 5 Error Codes Canon iR Download here the full version of service manual iR Code List. Thank you for purchasing the Canon iR/iR/iR Series Machine. This Manual describes the use of the List of Error Codes Without Messages.

Author: Arashill Kacage
Country: Netherlands
Language: English (Spanish)
Genre: Travel
Published (Last): 28 January 2017
Pages: 408
PDF File Size: 15.31 Mb
ePub File Size: 17.7 Mb
ISBN: 691-4-75106-890-7
Downloads: 28958
Price: Free* [*Free Regsitration Required]
Uploader: Kagrel

The main thermistor has an open circuit. The delivery motor relay harness is faulty.

Main cause The fixing motor M19 is faulty. E The communication between the copier and the finisher is disrupted and is not lisy for 5 sec or less.

Canon Ir 3300 Error Code List

The puncher driver PCB is faulty. The puncher waste sensor is faulty. The fixing heater has an open circuit.

The waste toner sensor is faulty. E While caanon ADF is in standby, the communication with its host machine is disrupted ir300 5 sec or more; or, while the ADF is in operation, the communication with its host machine is disrupted for 0. The aligning plate home position sensor S6 does not go OFF when the front alignment motor M3 is driven for a specific number code rotations.

Cause The rear alignment motor M4 is faulty. Main cause The connect has poor connection. E At the start of the motor CW operation, the stack handling motor M2 may be driven for a specific number of rotations; however, the stack delivery lever home position sensor S8 does not go ON.

  GURPS ESPIONAGE PDF

Check the wiring; if normal, replace the main controller PCB.

The main controller PCB is faulty. Main cause The connector has poor connector. Replace the main power supply PCB. The sub thermistor detects about C or higher Causes: Replace the sensor lever. Iir3300 heater drive power supply is faulty. If this error occurs frequently, however, a fault on the main controller PCB is a possibility.

Canon Ir Error Code List – Copy Care Enterprise

The stack delivery lever home position sensor S8 is faulty, the connector is disconnected, or an open circuit exits. When the fixing motor is rotating, is codfs film rotation detection signal sent by the fixing film sensor to the concoctor J of the DC controller PCB?

The thermistor control mechanism is faulty.

Action If this error occurs during normal copying or printing, the job in question image data is cleared when the main power switch is turned off and then on again; i. E The aligning plate rear does not leave home position when the alignment motor rear is driven for 3 sec. The heater has an open circuit, or the thermal switch is open. Archives December August July E The paddle does not leave home position when the paddle motor is driven for 2 sec or more.

  FH ANSBACH FERNSEHSTUDIO PDF

Cause The front alignment motor M3 is faulty. The horizontal registration assembly malfunctions because of the presence of foreign matter.

The main thermistor or the sub thermistor detects overheating hardware circuit detection Causes: Main cause The paddle home position sensor PI2 is faulty. Action If the error is still indicated after disposing of the waste toner, perform the following: Replace the fixing film unit.

E The intervals of zero-cross signals deviate from the tolerance range while the fixing heater is supplied with power.

Canon IR 3300 Error Code List

Main cause The fixing film sensor PS45 is faulty. The home position sensor does not go ON when the main power switch is turned on. Action See the description for E Categories Blog Manuals Service Specification. Is it 0 W short circuit? Ir33300 aligning plate home position sensor front; PI4 is faulty.

Main cause The scanning lamp is faulty. E The puncher not leave home position when the puncher shift motor is driven for 1 sec.

Author: admin