KEEP THIS MANUAL. Store this manual in a safe place for future reference. MEMORY BACKUP. • To protect your programmed memory contents, the DW- This page contains information about the Owner’s Manual for the DW from Korg. View and Download Korg DW owner’s manual online. DW Synthesizer pdf manual download.

Author: Mektilar Arashigami
Country: Puerto Rico
Language: English (Spanish)
Genre: Music
Published (Last): 26 June 2005
Pages: 269
PDF File Size: 13.23 Mb
ePub File Size: 20.53 Mb
ISBN: 211-4-80295-895-3
Downloads: 35313
Price: Free* [*Free Regsitration Required]
Uploader: Tulabar

We highly recommend that you do the installation yourself. If you are uncertain about your ability to open the DW and handle its components carefully, please refer the installation to a qualified technician. The chip will have the following identification printed directly on it: If you accidentally unplug any connectors, you may have difficulty getting a good contact when they are re-connected because the wires can be pulled away from the metal contacts inside the plugs.

Be careful not to break maual joystick. Lift up the top half, containing the keyboard and control panel just enough to detach it from the lover half. We need to remove the middle PCB. You must hold these buttons down until the display changes to Before opening the DW you mmanual understand that the top half is rather heavy and is connected to the bottom by several manuql and bundles of wires.

Purchased an Arduino Nano today to try this mod. Dw800 strongly suggest taking an hour to read the entire manual before beginning to use the Turbo-charged DW. Insert a new 3V cell into the holder, and the interlude is finished.

Use the plastic pen cap to make delicate adjustments if necessary.

Please find a technician who will cooperate. Test the location and then remove only a tiny piece of the backing mwnual at the left edge. This wipes the patches from memory, so if you want them then make sure you have saved them and know how to restore them using SYSEX or tape.


Those wt o are technically inclined may be tempted to solder the jumper and dispense with the clip. Once the board is started and you have double-checked manuall with a flashlight, use both thumbs to press directly downward on manuzl large chip that is directly behind the round lithium battery.

Most problems are easily solved in a few minutes with a simple explanation and instructions if you give us accurate and complete information about the problem.

DW-8000/Owner’s Manaul

If garbled display persists after initialization, you have made some error in installation and may wish to call for advice. Then use firmer pressure to seat the installation. Once the adhesive touches the DW it will not be possible to remove or adjust it.

Make sure it is cool. You may carefully remove it from its package. By the way, once TURBO is installed, the DW will remember what patch number was called up when the DW was turned off and it will select this patch when it comes back on.

This is the ROM chip which is designed to be replaceable. Don’t try to guess, Just tell us exactly what happened! Remember to bring the instruction manual along with the kit! Have the front key side towards you so that the joystick is now on your right, face down. I will give it a try for sure.

A flashlight is very handy here! About Us Contact Hackaday.

Korg DW-8000 Owner’s Manual

It is mnaual likely in dry environments caused by winter heating when cold air from outside is heated inside the home and needs far more moisture to maintain its relative humidy levels than it did outside.


Do not remove the four rubber feet or the 4 smaller screws located to the left and right of the rear left rubber foot.

Be sure that you double check afterwards to be sure that you actually connected to this pin! Fortunately these are all quite simple.


If a es contact with TURBO or any of DW it might damage the is please read the following Static electricity is less likely to build up in a humid environment. So take your time to get it all the way in! The one you are looking for is in the rear center and has 14 pins, white printing on the circuit board identifies it as IC number 29 “IC29”. I just bought an EX Observe the pin closest to you on the right side. Note that 10 is helpfully labelled on the silk screen! Do not wear a dw0800

Korg – DW – Owner’s Manual

In many cases initialization will not be necessary and TURBO will be ready to use as soon as it is installed. The plastic shaft of the clip will point up in the air at an angle in the direction of the right front. Do not pull or break this jumper cable.

The purpose of initialization is to remove garbled data that will confuse the DW ‘ s operating procedures and to clear garbled characters from the display.

Author: admin