ISO 23429 PDF

Gauging of hexagon sockets (ISO ); German version EN ISO ISO Gauging of hexagon sockets. standard by International Organization for Standardization, 01/15/ View all product details. Buy NF EN ISO Gauging Of Hexagon Sockets from SAI Global.

Author: Danos Nikogrel
Country: Albania
Language: English (Spanish)
Genre: Finance
Published (Last): 6 October 2009
Pages: 271
PDF File Size: 12.55 Mb
ePub File Size: 2.88 Mb
ISBN: 269-2-35742-939-6
Downloads: 80822
Price: Free* [*Free Regsitration Required]
Uploader: Nikobar

Intermediate nominal lengths according to ISO are permissible. Uso socket button head screw ISO – M12 40 – A version isso any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

Alternative form of socket permissible For broached sockets which are at the maximum limit of size the overcut resulting from drilling shall not exceed of the length of any flat of the socket which is. NOTE Particular attention is drawn to the note in Table 2 and to Table 3 concerning the limitation on ultimate tensile load. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

Technical Committee Mechanical fasteners Publisher and printing: Requirements for non-electrolytically applied zinc flake coatings are covered in ISO Acceptability Acceptance procedure is covered in ISO In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing.

  BLIND SPOTS BAZERMAN PDF

Standards New Zealand :: Gauging of hexagon sockets

Symbols and designations of dimensions are defined in ISO Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. Draft International Standards adopted by the technical io are circulated to the member bodies for voting.

In addition, when full-size screws are loaded using the type of testing fixture illustrated in ISOthey shall withstand, without fracture, the minimum ultimate tensile loads given in Table 3.

Every care has been taken to ensure that the file is suitable for use by ISO member bodies.

International organizations, governmental and is, in liaison with ISO, also take part in the work. This third edition cancels and replaces the second edition ISO For undated references, the latest edition of the referenced document including any amendments applies. Endorsement notice The text of ISO Table 3 — Minimum ultimate tensile loads for hexagon socket button head is of the values specified in ISO Thread Property class 8. In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy.

If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, e. Adobe is a trademark of Adobe Systems Incorporated.

  BLITZER PRECALCULUS 5E PDF

BS EN ISO – Gauging of hexagon sockets

They shall nevertheless meet the other material and property requirements for the respective property class specified in ISO Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.

The kso of preparing International Standards is normally carried out through ISO technical committees. For sio references, only the edition cited applies.

BS EN ISO 23429:2004

The main task of technical committees is to prepare International Standards. All rights reserved; No part of this publication may be reproduced or utilized in any form or by any means — elec- tronic, mechanical, photocopying or any other data carriers without prior permission from ON!

ISO shall not be held responsible for identifying any or all such patent rights. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Julyand conflicting national lso shall be withdrawn at the latest by July

Author: admin